|
Size: 2927
Comment:
|
Size: 3171
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 21: | Line 21: |
| Line 24: | Line 23: |
| Switch(config)# username <username> privilege 4 password <password> | |
| Line 25: | Line 25: |
| Switch(config-line)# login Switch(config-line)# line-password abc |
Switch(config-line)# login local Switch(config-line)# exit |
| Line 28: | Line 28: |
| }}} | }}} |
| Line 37: | Line 37: |
| }}} '''Configure Management IP''' {{{ Switch# configure terminal Switch(config)# management ip address 10.10.129.X/24 Switch(config)# exit Switch# show management ip address }}} '''Create VLANs''' {{{ Switch# configure terminal Switch# }}} '''Setup Management VLAN Interface''' Setup management on a vlan interface {{{ switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address |
|
| Line 51: | Line 76: |
'''Create VLANs''' {{{ Switch# configure terminal Switch# }}} '''Setup Management Interface''' Setup management on a vlan interface {{{ switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address }}} |
fs.com Switches purchased in 2021
Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:
|
Rack 1 |
Rack 2 |
Liebert |
Rack 4 |
Rack 5 |
01 |
R1S1:S58050-48T4Q |
R2S1:S5860-20SQ |
|
R4S1:S5800-48T4S |
R5S1:S5810-48TS-P |
02 |
R1S2:S58000-48T4S |
R2S2:S5800-48T4S |
|
|
|
03 |
|
R2S3:S5800-48T4S |
|
|
|
04 |
|
R2S4:S5800-48T4S |
|
|
|
R2S1:S5860-20SQ, 10.10.129.240 |
||||||||||||
R1S2 |
|
|
|
|
|
|
|
|
|
|
|
R1S1 |
INET1 |
INET2 |
|
|
|
|
|
|
|
|
|
|
|
Initial Setup Notes for 5800 Series Switches
SSH into the switch with the default user:pass = "admin:admin"
First Change the password, note that we are using local authentication mode, not "aaa" mode. What is aaa mode? That's for authenticating against a radius/TACACS+ server.
Switch# configure terminal Switch(config)# username <username> privilege 4 password <password> Switch(config)# line vty 0 7 Switch(config-line)# login local Switch(config-line)# exit Switch(config)# exit
Set the time
Switch# configure terminal Switch(config)# clock set datetime 11:30:00 10 26 2013 Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120 Switch(config)# exit
Configure Management IP
Switch# configure terminal Switch(config)# management ip address 10.10.129.X/24 Switch(config)# exit Switch# show management ip address
Create VLANs
Switch# configure terminal Switch#
Setup Management VLAN Interface
Setup management on a vlan interface
switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address
Set the banner to show the name of the switch
Switch# configure terminalThe // at the end of the line indicates the start of a comment: Switch# banner login # You are logged into RXSY # Switch# exit Switch# show running //validates that it worked
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Common Commands
The // at the end of the line indicates the start of a comment:
Show Port Status
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Show VLAN information for port
switch# show interface switchport interface eth-0-1
Backup and Restore the switch Configuration
To backup the configuration, ssh into the switch and perform the following:
Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf
To download a configuration file:
Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf