Differences between revisions 1 and 3 (spanning 2 versions)
⇤ ← Revision 1 as of 2010-03-29 01:15:59 →
Size: 19149
Editor: 24-183-238-75
Comment:
← Revision 3 as of 2010-03-29 01:20:58 → ⇥
Size: 19183
Editor: 24-183-238-75
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
= Firewall Examples = = Firewalls =

For a brief introduction see
Line 476: Line 478:
In the extremely simple NAT setup I do not forward anthing to the interior of the netwowrk, although I have some commented lines that used to do that. This too is from a long since dead network. In this extremely simple NAT setup I do not forward anthing to the interior of the network, although I have some commented lines that had been used to do that. This too is from a long since dead network.

Firewalls

For a brief introduction see

For now this page includes firewall examples that were used on an actual (although now non-existent) network. It successfully protected some 16 static IPs for six years. At one time I recorded a 3-way coordinated attack from university networks in Italy, France and Germany. Through all this time, the bridging firewall was used:

Bridge Setup

# /etc/rc.d/init.d/bridge
#
return=$rc_done
case "$1" in

    start)
        echo "Starting service bridge br0"
        ifconfig eth0 0.0.0.0 promisc 
        ifconfig eth1 0.0.0.0 promisc 
        brctl addbr br0 || return=$rc_failed
        brctl addif br0 eth0 || return=$rc_failed
        brctl addif br0 eth1 || return=$rc_failed
        brctl sethello br0 1 || return=$rc_failed
        brctl setmaxage br0 4 || return=$rc_failed
        brctl setfd br0 4 || return=$rc_failed
        ifconfig br0 promisc up 209.50.17.211 netmask 255.255.255.240 broadcast 209.50.17.223 || return=$rc_failed
        route add default gw 209.50.17.209
        echo -e "$return"
        ;;

    stop)
        echo "Shutting down service bridge br0"
        ifconfig br0 down || return=$rc_failed
        brctl delif br0 eth0 || return=$rc_failed
        brctl delif br0 eth1 || return=$rc_failed
        brctl delbr br0 || return=$rc_failed
        ifconfig eth0 down || return=$rc_failed
        ifconfig eth1 down || return=$rc_failed
        route del default
        echo -e "$return"
        ;;

    status)
        ifconfig br0
        brctl show br0
        ;;

    restart)
      $0 stop && $0 start || return=$rc_failed
      ;;

    *)
      echo "Usage: $0 {start|stop|status|restart}"
      exit 1
      esac
      test "$return" = "$rc_done" || exit 1

exit 0

Firewall Setup

# /etc/init.d/firewall
#
return=$rc_done
case "$1" in

start)

     ###############################################################################
     #SETUP INFORMATION
     INTERNET="eth0"
     DMZ="eth1"
     LOOPBACK_INTERFACE="lo"
     CONNECTION_TRACKING="1"
     ICMP_STRICT="1"
     L2TP="0"
     INET_SSH="0"

     BRAIN="209.50.17.210"
     BRAIN2="209.50.17.212"
     CISCO="209.50.17.209"
     YAKKO="209.50.17.215"
     CSE="129.93.165.2"
     TIMESERVER1="132.163.4.101"
     TIMESERVER2="132.163.4.102"
     TIMESERVER3="132.163.4.103"

     DMZ_NETWORK="209.50.17.213-222"

     SUBNET_BROADCAST="209.50.17.223"
     SUBNET_NETWORK="209.50.17.208"

     LOOPBACK="127.0.0.0/8"
     CLASS_A="10.0.0.0/8"
     CLASS_B="172.16.0.0/12"
     CLASS_C="192.168.0.0/16"
     CLASS_D_MULTICAST="224.0.0.0/4"
     CLASS_E_RESERVED_NET="240.0.0.0/5"
     BROADCAST_SRC="0.0.0.0"
     BROADCAST_DEST="255.255.255.255"

     PRIVPORTS="0:1023"
     UNPRIVPORTS="1024:65535"

     ###############################################################################
     # in /proc/sys/net/ipv4 protections available

     # Enable broadcast echo Protection
     echo 1 > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts

     # Disable Source Routed Packets
     for f in /proc/sys/net/ipv4/conf/*/accept_source_route; do
         echo 0 > $f
     done

     # Enable TCP SYN Cookie Protection
     echo 1 > /proc/sys/net/ipv4/tcp_syncookies

     # Disable ICMP Redirect Acceptance
     for f in /proc/sys/net/ipv4/conf/*/accept_redirects; do
         echo 0 > $f
     done

     # Don't Send Redirect Messages
     for f in /proc/sys/net/ipv4/conf/*/send_redirects; do
         echo 0 > $f
     done

     # Drop Spoofed Packets coming in on an interface, which if replied to,
     # would result in the reply going out a different interface.
     for f in /proc/sys/net/ipv4/conf/*/rp_filter; do
         echo 1 > $f
     done

     # Log packets with impossible addresses. (Do we really want to do this?)
     #for f in /proc/sys/net/ipv4/conf/*/log_martians; do
     #    echo 1 > $f
     #done

     ###############################################################################
     #FLUSH EVERYTHING AND DELETE CHAINS

     echo "Flushing all rules and chains ..."

     /sbin/iptables -F
     /sbin/iptables -t nat -F
     /sbin/iptables -t mangle -F

     /sbin/iptables --delete-chain
     /sbin/iptables -t nat --delete-chain
     /sbin/iptables -t mangle --delete-chain

     #DEFAULT POLICIES
     #default filter policy

     /sbin/iptables --policy INPUT DROP
     /sbin/iptables --policy OUTPUT DROP
     /sbin/iptables --policy FORWARD DROP

     #default nat policy
     /sbin/iptables -t nat --policy PREROUTING ACCEPT
     /sbin/iptables -t nat --policy OUTPUT ACCEPT
     /sbin/iptables -t nat --policy POSTROUTING ACCEPT

     #default mangle policy
     /sbin/iptables -t mangle --policy PREROUTING ACCEPT
     /sbin/iptables -t mangle --policy OUTPUT ACCEPT

     #Allow loopback
     /sbin/iptables -A INPUT -m physdev --physdev-in lo -j ACCEPT
     /sbin/iptables -A OUTPUT -m physdev --physdev-out lo -j ACCEPT

     ###############################################################################

     #CREATE VALIDATION CHAINS
     iptables -N TCP-STF
     iptables -N CON-TRK
     iptables -N SRC-CHK
     iptables -N FWL-OUT

     #CREATE TRAFFIC CHAINS
     iptables -N INET-SVRS
     iptables -N SVRS-INET

     #CREATE ICMP CHAINS
     iptables -N passicmp

     ###############################################################################

     echo "Creating firewall rules..."

     #INSERT A PACKET INTO THE APPROPRIATE CHAIN
     ## Allow SSH to DMZ
     /sbin/iptables -A INPUT -m physdev --physdev-in $DMZ -p tcp --destination-port 22 -j ACCEPT
     /sbin/iptables -A INPUT -m physdev --physdev-in $DMZ -p udp --destination-port 22 -j ACCEPT
     if [ $INET_SSH = 1 ] ; then
       /sbin/iptables -A INPUT -m physdev --physdev-in $INTERNET -p tcp --destination-port 22 -j ACCEPT
       /sbin/iptables -A INPUT -m physdev --physdev-in $INTERNET -p udp --destination-port 22 -j ACCEPT
     fi

     /sbin/iptables -A INPUT -d $SUBNET_BROADCAST -j DROP
     /sbin/iptables -A INPUT -p icmp -j passicmp
     /sbin/iptables -A INPUT -j TCP-STF
     /sbin/iptables -A INPUT -j CON-TRK
     /sbin/iptables -A INPUT -j SRC-CHK
     #/sbin/iptables -A INPUT -p tcp --destination-port 22 -j ACCEPT


     ################################################################################
     # On 9/28/03 we denied these idiots who are just hammering our site!
     /sbin/iptables -A INPUT -s 216.39.48.0/24 -j DROP
     /sbin/iptables -A FORWARD -s 216.39.48.0/24 -j DROP
     /sbin/iptables -A FORWARD -s 68.116.156.85 -j DROP
     /sbin/iptables -A FORWARD -s 213.37.82.0/24 -j DROP
     /sbin/iptables -A FORWARD -s 63.107.252.0/24 -p tcp --destination-port 25 -j DROP
     /sbin/iptables -A FORWARD -s 63.107.252.0/24 -p udp --destination-port 25 -j DROP
     /sbin/iptables -A FORWARD -s 65.212.41.0/24 -p tcp --destination-port 25 -j DROP
     /sbin/iptables -A FORWARD -s 65.212.41.0/24 -p udp --destination-port 25 -j DROP
     /sbin/iptables -A FORWARD -s 65.186.8.0/24 -j DROP

     #
     ################################################################################


     /sbin/iptables -A FORWARD -p icmp -j passicmp
     /sbin/iptables -A FORWARD -j TCP-STF
     /sbin/iptables -A FORWARD -j CON-TRK
     /sbin/iptables -A FORWARD -j SRC-CHK
     /sbin/iptables -A FORWARD -m physdev --physdev-in $INTERNET --physdev-out $DMZ -j INET-SVRS
     /sbin/iptables -A FORWARD -m physdev --physdev-in $DMZ --physdev-out $INTERNET -j SVRS-INET

     # Allow the firewall to talk to the DMZ
     /sbin/iptables -A OUTPUT -m physdev --physdev-out $DMZ -j ACCEPT
     # Otherwise do the normal check
     /sbin/iptables -A OUTPUT -p icmp -j passicmp
     /sbin/iptables -A OUTPUT -j TCP-STF
     /sbin/iptables -A OUTPUT -j CON-TRK
     /sbin/iptables -A OUTPUT -j SRC-CHK
     /sbin/iptables -A OUTPUT -m physdev --physdev-out $INTERNET -j FWL-OUT

     ##############################################################################
     # FWL-OUT What we allow the firewall to talk to


     # Allow this machine to talk to the internet over SSH
     /sbin/iptables -A FWL-OUT -p tcp --destination-port 22 -j ACCEPT
     /sbin/iptables -A FWL-OUT -p tcp -d 209.50.17.209 -j ACCEPT
     /sbin/iptables -A FWL-OUT -j DROP

     ###############################################################################
     # the ICMP chain

     # strict version:
     if [ $ICMP_STRICT = 1 ] ; then
         /sbin/iptables -A passicmp -p icmp --icmp-type destination-unreachable -j ACCEPT
         /sbin/iptables -A passicmp -p icmp --icmp-type source-quench -j ACCEPT
         /sbin/iptables -A passicmp -p icmp --icmp-type time-exceeded -j ACCEPT
         /sbin/iptables -A passicmp -p icmp -j DROP
     else
         /sbin/iptables -A passicmp -p icmp -j ACCEPT
     fi


     ###############################################################################
     #TCP-STATE-FLAGES

     # All of the bits are cleared
     iptables -A TCP-STF -p tcp --tcp-flags ALL NONE -j DROP

     # SYN and FIN are both set
     iptables -A TCP-STF -p tcp --tcp-flags SYN,FIN SYN,FIN -j DROP

     # SYN and RST are both set
     iptables -A TCP-STF -p tcp --tcp-flags SYN,RST SYN,RST -j DROP

     # FIN and RST are both set
     iptables -A TCP-STF -p tcp --tcp-flags FIN,RST FIN,RST -j DROP

     # FIN is the only bit set, without the expected accompanying ACK
     iptables -A TCP-STF -p tcp --tcp-flags ACK,FIN FIN -j DROP

     #PSH is the only bit set, without the expected accompanying ACK
     iptables -A TCP-STF -p tcp --tcp-flags ACK,PSH PSH -j DROP

     #URG is the only bit set, without the expected accompanyin
     iptables -A TCP-STF -p tcp --tcp-flags ACK,URG URG -j DROP

     ###############################################################################
     # Allows established and related connections through

     if [ $CONNECTION_TRACKING = 1 ] ; then
         iptables -A CON-TRK -m state --state ESTABLISHED,RELATED -j ACCEPT
         iptables -A CON-TRK -m state --state INVALID -j LOG --log-level info --log-prefix "CS"
         iptables -A CON-TRK -m state --state INVALID -j DROP
     fi


     ###############################################################################
     #Refuse various invalid sources

     # Refuse spoofed packets pretending to be from the external interface’s IP address
     iptables -A SRC-CHK -m physdev --physdev-in $INTERNET -s $BRAIN -j DROP

     #Refuse packets claiming to be from a Class A,B,C private network
     iptables -A SRC-CHK -s $CLASS_A -j DROP
     iptables -A SRC-CHK -s $CLASS_B -j DROP
     iptables -A SRC-CHK -s $CLASS_C -j DROP

     #Refuse multicast packets
     iptables -A SRC-CHK -s $CLASS_D_MULTICAST -j DROP
     iptables -A SRC-CHK -s $CLASS_E_RESERVED_NET -j DROP
     iptables -A SRC-CHK -d $BROADCAST_DEST -j DROP

     #Refuse packets claiming to be from loopback
     iptables -A SRC-CHK -m physdev --physdev-in $INTERNET -s $LOOPBACK -j DROP

     #Refuse malformed broadcast packests
     iptables -A SRC-CHK -s $BROADCAST_DEST -j DROP

     iptables -A SRC-CHK -s $BROADCAST_SRC -j DROP

     #Refuse directed broadcasts
     iptables -A SRC-CHK -m physdev --physdev-in $INTERNET -s $SUBNET_NETWORK -j DROP
     iptables -A SRC-CHK -m physdev --physdev-in $INTERNET -s $SUBNET_BROADCAST -j DROP

     ###############################################################################
     # Brain/Gateway Server Table
     # Currently we accept FTP, SMTP, DNS, WWW, POP3, NTP*
     # We have also added the private forwards at the bottom
     # this is for servers that on the private IP range


     # SMTP
     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 25 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 25 -j ACCEPT

     # Domain/Nameserver as of 9/28 this service is not available - no longer serving Inviationsource.com
     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 42 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 42 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 53 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 53 -j ACCEPT

     # WWW
     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 80 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 80 -j ACCEPT

     # WWW/SSL
     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 443 -j ACCEPT
     /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 443 -j ACCEPT

     # Allow time server to gateway
     /sbin/iptables -A INET-SVRS -s $TIMESERVER1 -d $BRAIN -p udp --destination-port 123 -j ACCEPT
     /sbin/iptables -A INET-SVRS -s $TIMESERVER2 -d $BRAIN -p udp --destination-port 123 -j ACCEPT
     /sbin/iptables -A INET-SVRS -s $TIMESERVER3 -d $BRAIN -p udp --destination-port 123 -j ACCEPT
     /sbin/iptables -A INET-SVRS -s $TIMESERVER1 -d $BRAIN2 -p udp --destination-port 123 -j ACCEPT
     /sbin/iptables -A INET-SVRS -s $TIMESERVER2 -d $BRAIN2 -p udp --destination-port 123 -j ACCEPT
     /sbin/iptables -A INET-SVRS -s $TIMESERVER3 -d $BRAIN2 -p udp --destination-port 123 -j ACCEPT

     # PPTP
#     /sbin/iptables -A INET-SVRS -d $BRAIN -p 47 -j ACCEPT
#     /sbin/iptables -A INET-SVRS -d $BRAIN -p tcp --destination-port 1723 -j ACCEPT
#     /sbin/iptables -A INET-SVRS -d $BRAIN2 -p 47 -j ACCEPT
#     /sbin/iptables -A INET-SVRS -d $BRAIN2 -p tcp --destination-port 1723 -j ACCEPT

     # L2TP/IPSec
     if [ $L2TP = 1 ] ; then
       /sbin/iptables -A INET-SVRS -d $BRAIN -p 50 -j ACCEPT
       /sbin/iptables -A INET-SVRS -d $BRAIN -p 51 -j ACCEPT
       /sbin/iptables -A INET-SVRS -d $BRAIN -p udp --destination-port 500 -j ACCEPT
       /sbin/iptables -A INET-SVRS -d $BRAIN2 -p 50 -j ACCEPT
       /sbin/iptables -A INET-SVRS -d $BRAIN2 -p 51 -j ACCEPT
       /sbin/iptables -A INET-SVRS -d $BRAIN2 -p udp --destination-port 500 -j ACCEPT
     fi

     # ALLOW X Apps from cse.unl.edu to yakko
     /sbin/iptables -A INET-SVRS -s $CSE -d $YAKKO -p tcp --destination-port 6000 -j ACCEPT
     #/sbin/iptables -A INET-SVRS -s $CSE -d $YAKKO -p udp --destination-port 6000 -j ACCEPT


     # PACKETS THAT MAKE IT THIS FAR ARE LOGGED AND DROPPED BY POLICY
     /sbin/iptables -A INET-SVRS -j LOG --log-level info --log-prefix "SC: "
     /sbin/iptables -A INET-SVRS -j DROP

     ###############################################################################
     # SVRS-INET'

     # Allow out SMTP
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --source-port 25 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --source-port 25 -j ACCEPT

     # Allow out nameserver
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --source-port 42 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --source-port 42 -j ACCEPT

     # Allow out Domain (DNS)
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --source-port 53 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --source-port 53 -j ACCEPT

     # Allow out HTTP(s)
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --source-port 80 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --source-port 80 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --source-port 443 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --source-port 443 -j ACCEPT

     # Allow NTP requests out
     /sbin/iptables -A SVRS-INET -s $BRAIN -d $TIMESERVER1 -p udp --source-port 123 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -d $TIMESERVER2 -p udp --source-port 123 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -d $TIMESERVER3 -p udp --source-port 123 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN2 -d $TIMESERVER1 -p udp --source-port 123 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN2 -d $TIMESERVER2 -p udp --source-port 123 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN2 -d $TIMESERVER3 -p udp --source-port 123 -j ACCEPT

     # PPTP Is currently not allowed instead use L2TP
#     /sbin/iptables -A SVRS-INET -s $BRAIN -p 47 -j ACCEPT
#     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --destination-port 1723 -j ACCEPT
#     /sbin/iptables -A SVRS-INET -s $BRAIN2 -p 47 -j ACCEPT
#     /sbin/iptables -A SVRS-INET -s $BRAIN2 -p tcp --destination-port 1723 -j ACCEPT

     # Next four lines stop anyone except our mail server from sending mail
     /sbin/iptables -A SVRS-INET -s $BRAIN -p tcp --destination-port 25 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s $BRAIN -p udp --destination-port 25 -j ACCEPT
     /sbin/iptables -A SVRS-INET -s 0.0.0.0 -p tcp --destination-port 25 -j DROP
     /sbin/iptables -A SVRS-INET -s 0.0.0.0 -p udp --destination-port 25 -j DROP

     # These lines allow any activity outbound on unprivileged ports all
     # other outbound traffic is denied by policy
     /sbin/iptables -A SVRS-INET -p tcp --source-port 1024:65535 -j ACCEPT
     /sbin/iptables -A SVRS-INET -p udp --source-port 1024:65535 -j ACCEPT

     echo "Finished Firewall setup."
     ;;

stop)

     echo "Flushing all rules and chains ..."

     /sbin/iptables -F
     /sbin/iptables -t nat -F
     /sbin/iptables -t mangle -F

     /sbin/iptables --delete-chain
     /sbin/iptables -t nat --delete-chain
     /sbin/iptables -t mangle --delete-chain

     /sbin/iptables --policy INPUT ACCEPT
     /sbin/iptables --policy OUTPUT ACCEPT
     /sbin/iptables --policy FORWARD ACCEPT

     #default nat policy
     /sbin/iptables -t nat --policy PREROUTING ACCEPT
     /sbin/iptables -t nat --policy OUTPUT ACCEPT
     /sbin/iptables -t nat --policy POSTROUTING ACCEPT

     #default mangle policy
     /sbin/iptables -t mangle --policy PREROUTING ACCEPT
     /sbin/iptables -t mangle --policy OUTPUT ACCEPT
     ;;
restart)

     /etc/init.d/firewall stop && /etc/init.d/firewall start
     ;;
*)
     echo "use firewall [start|stop]"

     exit 1

esac

test "$return" = "$rc_done" || exit 1

exit 0

At times, I have also used NAT

In this extremely simple NAT setup I do not forward anthing to the interior of the network, although I have some commented lines that had been used to do that. This too is from a long since dead network. 

#Postrouting nat stuff from 10.0.0.0
iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -o eth0 -j SNAT --to-source x.y.z.21

# DON'T DO IT ANYMORE BECAUSE WE GOT A REGUALR IP FOR PINKY 220 - 5/30/03
#Pre routing stuff to Pinky
#iptables -t nat -A PREROUTING -i eth0 -p tcp -d x.y.z.22 --sport 1024:65535 --dport 80 -j DNAT --to-destination 10.0.0.2
#iptables -t nat -A PREROUTING -i eth1 -p tcp -d x.y.z.22 --sport 1024:65535 --dport 80 -j DNAT --to-destination 10.0.0.2

Once you have NAT setup, there really isn't much difference in how the firewall is setup. You can use the one listed above.

NetworkSecurity/FireWall (last edited 2019-03-24 23:30:37 by 68)