Differences between revisions 20 and 27 (spanning 7 versions)
⇤ ← Revision 20 as of 2019-08-09 23:12:41 →
Size: 2282
Editor: scot
Comment:
← Revision 27 as of 2020-08-11 17:55:26 → ⇥
Size: 2453
Editor: scot
Comment:
Deletions are marked like this. Additions are marked like this.
Line 16: Line 16:
Install Windows 2012 on one of your remaining VMs. Install Windows Server on one of your remaining VMs.
Line 20: Line 20:
On windows setup your your network with the following information: On windows setup your network with the following information:
Line 26: Line 26:
Change your server to allow remote access (from the server console). To do this, run sconfig (if you have a GUI, you are doing it wrong). While you are at it, make sure you've got all of the following configured:
Line 28: Line 28:
Make sure you can access the Internet and that you can remote desktop into your machine. You will need to enable remote desktop on your Windows Machine - I did not show you how to do this in the video. Plus you will need to change the profile on the Windows Firewall to allow public access with edge traversal. These are shown below.  1. [no change]
 1. Set to CPTE230A
 1. [no change]
 1. Enable remote access
 1. [no change]
 1. [no change]
 1. Enable remote desktop
 1. Configure your network settings here.
 1. Set the timezone to Eastern
 1. [no change]
 1. If you haven't done it yet, enter the key and activate your server
 1. [No change ....]
Line 30: Line 41:
{{attachment:firewall1.png}} {{attachment:sconfig.png||width=800}}
Line 32: Line 43:
{{attachment:firewall2.png}} Make sure you can access the Internet and that you can remote desktop into your machine.
Line 46: Line 57:
||Video shows working windows 2012 installation ||40 || ||Video shows working windows 2019 installation (ping internet from commandline) ||40 ||

Lab 01

Installing Windows Server.

Please read the entire lab before starting.

Assignment

First read the naming convention before you do anything!

For example, my machines are named:

  • router
  • cpte230a

Configure your Linux firewall as shown here.

Install Windows Server on one of your remaining VMs.

Use one of these keys

On windows setup your network with the following information:

  • IP address 192.168.1.2
  • Gateway 192.168.1.1
  • DNS 10.10.129.2 and optionally 10.10.129.3 (We will change this soon)

To do this, run sconfig (if you have a GUI, you are doing it wrong). While you are at it, make sure you've got all of the following configured:

  1. [no change]
  2. Set to CPTE230A
  3. [no change]
  4. Enable remote access
  5. [no change]
  6. [no change]
  7. Enable remote desktop
  8. Configure your network settings here.
  9. Set the timezone to Eastern
  10. [no change]
  11. If you haven't done it yet, enter the key and activate your server
  12. [No change ....]

[ATTACH]

Make sure you can access the Internet and that you can remote desktop into your machine.

To earn points:

Create a homepage on your Documentation Wiki and include links to the following pages:

  1. Document the configuration of your network in a new page called “Networking" using the principles of documenting that we went over in class. Draw a diagram like you see on the wiki, but make sure it has your correct IP addresses.
  2. Document the process of installing Windows Server (Screen shots are good documenting choices during the install) in a new “Install” page of your wiki on moodle.
  3. Document your passwords in a new "Passwords" page of your wiki.

Create a video that shows your working Windows Server installation working. Include a walk through of your wiki pages.

Grade Guide

Topics

Points

Video shows working windows 2019 installation (ping internet from commandline)

40

Video talks through your Networking Documentation

10

Video talks through your Installation Documentation

10

Video Talks through your Passwords Documentation

10

Wiki contains a home page with links to the three pages listed above

30

WindowsAdministration/Lab01ConfigureLinuxInstallWindowsServer (last edited 2024-09-05 17:22:03 by scot)