Differences between revisions 10 and 17 (spanning 7 versions)
⇤ ← Revision 10 as of 2015-08-18 23:50:33 →
Size: 1923
Editor: scot
Comment:
← Revision 17 as of 2021-10-07 18:35:26 → ⇥
Size: 2331
Editor: scot
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:
In this lab we will setup a DHCP server and a Windows 8.1 client that uses it. In this lab we will setup a DHCP server and use it from the Windows 10 Client.
Line 5: Line 5:
  a. Setup the DHCP server on CPTE230C
  a. Install the DHCP Server tools "feature" on CPTE230A (Remember we will do most of our administration from CPTE230a.
 1. Using the DHCP manager on CPTE230A setup a scope called 192.168.1.0/24
  a. The range of addresses should go from 192.168.1.10 - 192.168.1.254		   a. Setup the DHCP server on CPTE230a include the tools.
  a. Install the DHCP Server tools "feature" on CPTE230w windows 10 machine (Remember we will do most of our administration from CPTE230c)
 1. Using the DHCP manager on CPTE230a setup a scope called 192.168.1.0/24
  a. The range of addresses should go from 192.168.1.100 - 192.168.1.254
Line 13: Line 13:
  a. Make sure DNS is set to 192.168.1.2   a. Make sure DNS is set to 192.168.1.2 and 192.168.1.3
Line 16: Line 16:
  a. Create a reservation for your windows 10 machine and set it to always get 192.168.1.10
Line 17: Line 18:
 1. Turn off the DHCP Service in OpnSense.
  a. Expand Services, DHCPv4, [LAN]
  a. Uncheck "Enable DHCP server on the LAN interface", then go to the bottom and save.
     a. (optionally copied the reserved MAC address)
 1. Back in the DHCP server create a reservation for your cptr230w machine (windows 10)
  a. Right click on Reservations and select New Rservation
  a. Fill in a reservation name, IP Address = 192.168.1.10, MAC address that you copied from the other reservation on OpnSense, Click add.
  a. From a command prompt type: ipconfig /release
  a. From a command prompt type: ipconfig /renew
  a. verify that your DHCP server is now 192.168.1.2 instead of 192.168.1.1.
Line 18: Line 29:
Install a Windows 8.1 Client and configure it to use DHCP
Line 20: Line 30:
 1. Name the server "cpte230d" with your username prefixed as appropriate (i.e. following the naming conventions mentioned on the [[WindowsAdministration/VirtualMachineNamingConvention|Naming Convention]] page.)
 1. Install Windows 8.1
 1. Create a username - dra, and document the password (Do not use a Microsoft Account).		 Configure your Windows 10 Client to use DHCP (if it is not already)
Line 24: Line 33:
 1. Add it to your primary domain {{{[username].internal}}}

Install a few things of use on the client:

 1. Install the RSAT tools
 1. Install Firefox		  1. Verify that you can manage the DHCP server from your windows 10 machine (login as administrator).
Line 40: Line 44:
||Video shows: Using client machine to access the internet with firefox. ||25 ||
||Video shows: Client configured to use the DHCP server with ipconfig /all ||25 ||
||Video shows: run the RSAT tool "Active Directory Users and Computers" from the client machine ||30 ||		 ||Video shows: Client configured to use the DHCP server with ipconfig /all ||50 ||
||Video shows: run the RSAT tool DHCP - logged in as administrator and shows the configured settings for your scope ||30 ||

Lab 06: DHCP

In this lab we will setup a DHCP server and use it from the Windows 10 Client.

  1. Setup a DHCP server
    1. Setup the DHCP server on CPTE230a include the tools.
    2. Install the DHCP Server tools "feature" on CPTE230w windows 10 machine (Remember we will do most of our administration from CPTE230c)
  2. Using the DHCP manager on CPTE230a setup a scope called 192.168.1.0/24
    1. The range of addresses should go from 192.168.1.100 - 192.168.1.254
    2. Length = 24
    3. Subnet Mask = 255.255.255.0
    4. Click next accepting defaults until you get to the "Configure DHCP Options" - Yes
    5. Router = 192.168.1.1
    6. Make sure DNS is set to 192.168.1.2 and 192.168.1.3
    7. Skip WINS server configuration
    8. Answer Yes, I want to activate this scope now.
    9. Create a reservation for your windows 10 machine and set it to always get 192.168.1.10
    10. Finish.

  3. Turn off the DHCP Service in OpnSense.

    1. Expand Services, DHCPv4, [LAN]
    2. Uncheck "Enable DHCP server on the LAN interface", then go to the bottom and save.
      1. (optionally copied the reserved MAC address)
  4. Back in the DHCP server create a reservation for your cptr230w machine (windows 10)
    1. Right click on Reservations and select New Rservation

    2. Fill in a reservation name, IP Address = 192.168.1.10, MAC address that you copied from the other reservation on OpnSense, Click add.

    3. From a command prompt type: ipconfig /release
    4. From a command prompt type: ipconfig /renew
    5. verify that your DHCP server is now 192.168.1.2 instead of 192.168.1.1.

Configure your Windows 10 Client to use DHCP (if it is not already)

  1. Verify that you can surf the internet from this machine.
  2. Verify that you can manage the DHCP server from your windows 10 machine (login as administrator).

Documentation

Document your work on the networking page in a new section called DHCP. Include:

  • Server DHCP install
  • IP range available
  • Scope options

Video Grade Guide

Topics

Points

Video shows: Client configured to use the DHCP server with ipconfig /all

50

Video shows: run the RSAT tool DHCP - logged in as administrator and shows the configured settings for your scope

30

Video talks through the documentation additions.

20

WindowsAdministration/Lab06Dhcp (last edited 2023-10-26 17:21:23 by scot)